Engineering Design and Manufacturing Group - Formerly JKRP

Engineering Design and Manufacturing Group - Formerly JKRP Department of Engineering Design and Manufacture which was once known as the CAD/CAM unit was establ At that time, there were about 25 manufacturing students.

In 1996, the unit started offering the Bachelors Degree in Computer Aided Design and Manufacturing (CAD/M) where at that time, there was about 25 students. The following year, the unit began offering a course in Manufacturing engineering which was once offered by the Mechanical Engineering department. However, since both manufacturing and CAD/M areas are closely related to each other, for session

1997/1998, the university management has approved the proposal for the manufacturing course to be transferred to the CAD/CAM unit. Therefore, teaching and support staffs, and equipment related to manufacturing course were transferred to the CAD/CAM unit. As a result of the transfer, the CAD/CAM unit was changed to the CAD/CAM and Manufacturing unit. Even though the CAD/CAM and Manufacturing unit offered two different courses, teaching staffs from both areas were involved as the areas are closely related to one another. In year 2000, with the offering of two courses and rapid development of the unit, it was upgraded to Department of Engineering Design and Manufacture (DEDM). Starting from 2000/2001 session, a four years studying system was implemented. Since 2015/16 session, the department is merged into Department of Mechanical Engineering. Vision

To be a world class engineering faculty that is recognized at the international level.

Get to know our professors & lecturers! style! EN-GI-NEE-RING! https://youtu.be/CYRpv-cMqx0*not for commercial use, so...
21/09/2017

Get to know our professors & lecturers! style!

EN-GI-NEE-RING!

https://youtu.be/CYRpv-cMqx0

*not for commercial use, song credit to the original singers*

29/04/2016

Dear beloved alumni of JKRP, please spare some of your precious time to provide a feedback to help us improve our service. http://bit.ly/24oilXO

20/11/2015
Need to experience ANSYS? Click this URL http://www.ansys.com/student
18/08/2015

Need to experience ANSYS? Click this URL http://www.ansys.com/student

ANSYS Student gives you the tools you'll use in your future careers. Learn the fundamentals of simulation while gaining experience using our state-of-the-art ANSYS Workbench simulation workflow.

Dear beloved alumni of JKRP, please spare some of your precious time to provide a feedback to help us improve our servic...
06/11/2014

Dear beloved alumni of JKRP, please spare some of your precious time to provide a feedback to help us improve our service. http://bit.ly/1u1V51z

23/07/2013
Will we be able to travel this way in our life time? Well, Tesla founder, Elon Musk wants to revolutionize transportatio...
17/07/2013

Will we be able to travel this way in our life time? Well, Tesla founder, Elon Musk wants to revolutionize transportation.

http://www.wired.com/autopia/2013/07/elon-musk-hyperloop/

Elon Musk wants to revolutionize transportation. Again. The serial entrepreneur envisions a future where mag-lev trains in enormous pneumatic tubes whisk us from Los Angeles to New York in 45 minutes. Need to be in Beijing tomorrow? No problem. It's a two-hour ride away.

10/06/2013

Sesi penerangan Robot Kuka oleh En. Zulkefle

6 Jun 2013
10/06/2013

6 Jun 2013

Fully paid PhD Opportunity in Wollongong, Australia. Contact Dr. Khay Wai See (kwsee@uow.edu.au) with your CV and a 2-pa...
31/05/2013

Fully paid PhD Opportunity in Wollongong, Australia. Contact Dr. Khay Wai See ([email protected]) with your CV and a 2-page project proposal.

Address

Department Of Engineering Design And Manufacture, Faculty Of Engineering, Universiti Malaya
Kuala Lumpur
50603

Website

Alerts

Be the first to know and let us send you an email when Engineering Design and Manufacturing Group - Formerly JKRP posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The School

Send a message to Engineering Design and Manufacturing Group - Formerly JKRP:

Shortcuts

Share

Category