Millwright Tech

Millwright Tech “Millwright | Fitter | Plant Maintenance
Motor Alignment • Bearing • Pump • Gearbox • Industrial Training”

What Does PN 16 Mean on a Valve? 🔧PN means Nominal Pressure. A PN 16 valve is generally rated for 16 bar (approximately ...
05/09/2026

What Does PN 16 Mean on a Valve? 🔧
PN means Nominal Pressure. A PN 16 valve is generally rated for 16 bar (approximately 232 PSI) at 20°C. The actual allowable pressure depends on the valve material and operating temperature.

🔩 What does 8.8 on a bolt mean?The first digit indicates 800 MPa tensile strength, while the second digit gives 640 MPa ...
05/09/2026

🔩 What does 8.8 on a bolt mean?
The first digit indicates 800 MPa tensile strength, while the second digit gives 640 MPa yield strength. Always select the correct bolt property class for safe and reliable work.
Did you know this? Comment below! 👇

Incorrect V-belt tension can damage the belt, bearings, and shaft. A loose belt slips and overheats, while an overly tig...
05/09/2026

Incorrect V-belt tension can damage the belt, bearings, and shaft. A loose belt slips and overheats, while an overly tight belt creates excessive bearing load. Always maintain the correct tension for longer equipment life.

⚠️ 5 Signs of Pump CavitationGravel-like noise, abnormal vibration, fluctuating pressure and flow, reduced performance, ...
04/09/2026

⚠️ 5 Signs of Pump Cavitation
Gravel-like noise, abnormal vibration, fluctuating pressure and flow, reduced performance, and impeller pitting are common warning signs. Inspect the pump early to prevent serious damage.

Mechanical Seal vs Gland Packing 🔧Mechanical seals provide better leak control and less shaft wear, while gland packing ...
04/09/2026

Mechanical Seal vs Gland Packing 🔧
Mechanical seals provide better leak control and less shaft wear, while gland packing is simple, economical, and requires slight leakage for cooling.
Which sealing method do you prefer? Comment below! 👇

Can you find the missing bottom reading? 🤔Comment your answer: A, B, C, or D.
04/09/2026

Can you find the missing bottom reading? 🤔
Comment your answer: A, B, C, or D.

Identify DE and NDE bearings correctly! ⚙️DE means Drive End, while NDE means Non-Drive End. The bearing arrangement may...
04/09/2026

Identify DE and NDE bearings correctly! ⚙️
DE means Drive End, while NDE means Non-Drive End. The bearing arrangement may vary depending on the machine design.

04/09/2026

Decode Bearing 3216! ⚙️
3 = Double-Row Angular Contact Ball Bearing
2 = Duty & Dimension Series
16 × 5 = 80 mm Bore Size

Shaft Runout vs Misalignment ⚙️Runout is a wobble in one rotating shaft, while misalignment occurs when two shaft center...
04/09/2026

Shaft Runout vs Misalignment ⚙️
Runout is a wobble in one rotating shaft, while misalignment occurs when two shaft centerlines are not aligned. Correct diagnosis prevents vibration and bearing failure.

Can you solve this alignment question? 🔧Bottom dial reading is −4.30 mm. What shim correction is required?Comment your a...
04/09/2026

Can you solve this alignment question? 🔧
Bottom dial reading is −4.30 mm. What shim correction is required?
Comment your answer: A, B, C, or D.

Address

Gopalganj

Website

Alerts

Be the first to know and let us send you an email when Millwright Tech posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category