⚡ CAN THIS OLD ANALYSER BE BROUGHT BACK TO LIFE? — PART TWO ⚡
With the Maester 1000 Plus opened up, it was time to continue investigating, test a few components and see whether I could get any signs of life from this old analyser.
But did I manage to bring it back from the dead—or has this challenge got the better of me? 👀
Watch Part Two to see how I got on.
And this might not be the end of the Maester just yet…
If you’ve got a good understanding of electrical components and would like to JOIN ME IN A FUTURE VIDEO to help investigate it further, leave a comment or send us a message ⚡
Tomkat Gas Training Ltd
Domestic gas training, ACS support, technical resources and practical trade content for new and established gas engineers. Training • Calculators • Community
Become a Gas Engineer with TomKat
We provide training and assessment for both new entrants and experienced engineers, including:
* ACS Initial and Reassessment
* LPG
* Water Regulations
* Unvented Hot Water Systems
* MET1 and additional ACS modules
* Ongoing technical support and mentoring
Whether you’re just starting your journey or looking to expand your qualifications, we’re here to help. Co
⚡ CAN THIS OLD ANALYSER BE BROUGHT BACK TO LIFE? ⚡
One of my followers sent me this Maester 1000 Plus with a challenge: see if I could get it working again.
I’m never one to turn down a project, so I opened it up to investigate and began attempting to revive it.
Things took a rather unexpected turn... 💥😂
Watch until the end—and come back for Part Two to find out whether I was able to get this analyser working again!
Would you have attempted to repair it?
Let me know in the comments 💬🔥
💨 PLUME MANAGEMENT KITS—DO YOU KNOW THE REQUIREMENTS? 💨
There seems to be a lot of confusion about when a plume management kit can be used, particularly when the original flue position doesn’t comply. 🤔
A plume management kit can’t simply be used to get around an incorrectly positioned installation unless the boiler manufacturer permits it.
In this video, I refer to BS 5440-1 and Technical Bulletin 016 to explain an important distinction:
➡️ The air inlet must be positioned at least 150 mm from the window frame due to structural and temperature considerations.
➡️ The POC outlet must be positioned at least 300 mm from the opening itself, to reduce the risk of products of combustion entering the building.
The frame and the opening aren’t the same measurement point and getting that distinction wrong could result in a non-compliant installation. ❌
Have you seen many plume management kits positioned incorrectly?
Let me know in the comments 💬🔥
11/08/2026
🔧 ONE FOR THE ENGINEERS WHO’VE SEEN IT ALL… 🔧
A subscriber recently sent me these photographs after coming across this setup.
I’ve got my suspicions about what I’m looking at—but before I reveal anything, I want to hand this one over to you lot 👀
Do you recognise it?
Let me know what you think in the comments—and bonus points if you’ve actually installed or worked on one before 💬🔥
Thanks to our subscriber for sending the photographs in. He would also like it formally recorded that he was not responsible for the pipework 😂
Wayne Burgess
10/08/2026
🏆 A LITTLE THROWBACK… 🏆
A few months ago, TomKat was incredibly proud to receive an Innovation Award for our collection of free gas-engineering calculators.
Each tool was created to provide engineers with quick, practical support for the calculations they carry out day-to-day.
It was a very proud moment for TomKat, and we're far too honoured not to share it with you all again!
You can try all of our FREE🔥 calculators here:
https://tom-kat.co.uk/gas-tools/
🎉 THE TOMKAT UK TOUR—AND YOU’RE INVITED TO THE PARTY! 🎉
Plans for the TomKat UK Tour are well underway, and in this video I’m sharing more about the companies joining us on the road—as well as our end-of-tour party! 🚐🔥
I’m pleased to announce that the tour is being supported by:
🔵 Wavin
🔵 Direct Plumbing Supplies
🔵 Alpha Press
🔵 Hotun
🔵 TPI
🔵 Trappex
🔵 PressCal
🔵 Sauermann
A huge thank you to every one of our sponsors for getting behind the tour and helping us bring it to life.
I also reveal what we’re planning for the end-of-tour party, where it will be held and how you can come along and join us! 🎉
Head over to our website to register your interest for the tour:
https://tom-kat.co.uk/register-interest/
🔥YOU’VE HAD YOUR SAY—NOW HERE’S MINE! 🔥
Part One sparked plenty of discussion, with some different opinions on how these fire faults should be classified.
In Part Two, I reveal the faults I identified, explain my verdict for each installation and talk through the reasoning behind my decisions.
Were they ID, AR or NCS—and what action should be taken?
Watch the full video to find out whether your answers matched mine 👀
Do you agree with my verdicts, or would you have classified any of them differently? Let me know down in the comments 💬
🔥 YOU’VE ARRIVED ON SITE—WHAT’S YOUR VERDICT? 🔥
I’ve got four fire installations for you to inspect today, and there’s something wrong in every one.
Put yourself in the engineer’s position: you’ve seen the installation, spoken to the customer, and now you need to decide what happens next.
What fault have you identified?
How would you classify or record it?
Most importantly—what action would you take?
Some of these may divide opinion, so don’t just give me your verdict—tell me the reasoning behind it 👀
I’ll be sharing my answers in Part Two.
🚨 FLUE FAULTS QUIZ — THE ANSWERS 🚨
Yesterday, I asked you to inspect these flue installations and decide what action you would take and how you would classify each one. 👀
Today, I reveal my answers. ✅
Did you reach the same verdict—or are there any you disagree with? 🤔
Let me know in the comments 💬🔥
Click here to claim your Sponsored Listing.
Location
Category
Contact the school
Website
Address
Ashton-Under-Lyne
OL67SB
Opening Hours
| Monday | 9am - 5:30pm |
| Tuesday | 9am - 5:30pm |
| Wednesday | 9am - 5:30pm |
| Thursday | 9am - 5:30pm |
| Friday | 9am - 5:30pm |
| Saturday | 9am - 4pm |
| Sunday | 9am - 4pm |